Distilled coconut fatty acid

Loading ...
Global Do...
Science
MSDS
<p>MATERIAL SAFETY DATA SHEET
DISTILLED COCONUT FATTY ACID
3. HAZARDS IDENTIFICATION
Harmful if inhaled, absorbed through skin, or swallowed. Causes skin and eye irritation. Mists or sprays 
are irritating to eyes and respiratory tract. See "Other Health Effects" Section. Can decompose at high 
temperatures forming toxic gases. Contents may develop pressure on prolonged exposure to heat.
EMERGENCY OVERVIEW:
POTENTIAL HEALTH EFFECTS
Inhalation is not a likely route of exposure at normally encountered temperatures. Contact with mist or 
spray may cause irritation of mucous membranes, coughing and difficulty in breathing. See "Other 
Health Effects" Section.
Inhalation:
Skin contact can cause irritation, especially under the finger nails (and other confined spaces such as 
under rings or watch bands). May cause defatting, drying and cracking of the skin. Prolonged and 
repeated contact may lead to dermatitis.
Skin Contact:
A single, prolonged skin exposure is not likely to result in the absorption of toxic amounts of the material.
Skin Absorption:
This product causes irritation, redness and pain.
Eye Contact:
EMERGENCY TELEPHONE NUMBERS (FOR EMERGENCIES INVOLVING CHEMICAL SPILLS OR RELEASE)
Toronto, ON  (416) 226-6117                     Montreal, QC (514) 861-1211                     Winnipeg, MB (204) 943-8827
Edmonton, AB (780) 424-1754                  Calgary, AB  (403) 263-8660                       Vancouver, BC (604) 685-5036
1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
Brenntag Canada Inc.
43 Jutland Rd.
Toronto, ON
M8Z 2G6
(416) 259-8231
Website:  http:\\www.brenntag.ca
WHMIS#:
00064740
Index: 
2008 June 25
PRODUCT IDENTIFICATION
Distilled Coconut Fatty Acid.
Product Name:  
2008 June 25
Date of Revision:
Effective Date:
HCI3562/08B
Not available.
Chemical Name:
Emery 622 Coconut Fatty Acid; Crude Coconut Fatty Acid.
Synonyms:
Mixed fatty acid.
Chemical Family:
CH3(CH3)nCOOH
Molecular Formula:
Manufacture of soaps. Chemical intermediate.
Product Use:
WHMIS Classification / Symbol:
READ THE ENTIRE MSDS FOR THE COMPLETE HAZARD EVALUATION OF THIS PRODUCT.
D-2B:  Toxic (skin and eye irritant)
Ingredient
CAS#
ACGIH TLV
% Concentration
2. COMPOSITION, INFORMATION ON INGREDIENTS (Not Intended As Specifications)
Fatty Acids, coco
61788-47-4
— 
95 - 100
Distilled Coconut Fatty Acid
Brenntag Canada Inc.
Date of Revision:
2008 June 25
WHMIS Number :
00064740
Page 2 of 6
4. FIRST AID MEASURES
FIRST AID PROCEDURES
Move victim to fresh air.  Give artificial respiration ONLY if breathing has stopped.  Give 
cardiopulmonary resuscitation (CPR) if there is no breathing AND no pulse.  Obtain medical attention 
IMMEDIATELY.
Inhalation:
Start flushing while removing contaminated clothing. Wash affected areas thoroughly with soap and 
water. If irritation, redness, or a burning sensation develops and persists, repeat flushing and obtain 
medical attention.
Skin Contact:
Immediately flush eyes with running water for a minimum of 20 minutes.  Hold eyelids open during 
flushing.  If irritation persists, repeat flushing.  Obtain medical attention IMMEDIATELY.
Eye Contact:
Do not attempt to give anything by mouth to an unconscious person. If victim is alert and not 
convulsing, rinse mouth out and give 1/2 to 1 glass of water to dilute material.  IMMEDIATELY contact 
local Poison Control Centre.  Vomiting should only be induced under the direction of a physician or a 
poison control centre.  If spontaneous vomiting occurs, have victim lean forward with head down to 
avoid breathing in of vomitus, rinse mouth and administer more water.  IMMEDIATELY transport victim 
to an emergency facility.
Ingestion:
Treat symptomatically. Medical conditions that may be aggravated by exposure to this product include 
diseases of the skin, eyes or respiratory tract.
Note to Physicians:
This product causes irritation, a burning sensation of the mouth and throat and abdominal pain.
Ingestion:
Effects (irritancy) on the skin and eyes may be delayed, and damage may occur without the sensation 
or onset of pain.  Strict adherence to first aid measures following any exposure is essential.
Other Health Effects:
5. FIRE-FIGHTING MEASURES
Flashpoint (°C)
AutoIgnition 
Temperature (°C)
LEL
UEL
Flammability Limits in Air (%):  
157.  (3)
Not available.
Not available.
Not available.
Flammability Class (WHMIS):
Thermal decomposition products are toxic and may include oxides of carbon and irritating gases.
Hazardous Combustion 
Products:
Do not direct a solid stream of foam into hot, burning pools.  This may cause spattering and increase 
fire intensity. Closed containers exposed to heat may burst. Spilled material may cause floors and 
contact surfaces to become slippery.
Unusual Fire or Explosion 
Hazards:
Not expected to be sensitive to mechanical impact.
Sensitivity to Mechanical Impact:
Not available.
Rate of Burning:
Not available.
Explosive Power:
Not expected to be sensitive to static discharge.
Sensitivity to Static Discharge:
EXTINGUISHING MEDIA
Dry chemical, carbon dioxide or water spray.
Fire Extinguishing Media:
FIRE FIGHTING 
INSTRUCTIONS
Isolate materials that are not involved in the fire and protect personnel.  Cool containers with flooding 
quantities of water until well after the fire is out. Spilled material may cause floors and contact surfaces 
to become slippery.
Instructions to the Fire Fighters:
Use self-contained breathing apparatus and protective clothing.
Fire Fighting Protective 
Equipment:
6. ACCIDENTAL RELEASE MEASURES
Information in this section is for responding to spills, leaks or releases in order to prevent or minimize the adverse effects on persons, 
property and the environment.  There may be specific reporting requirements associated with spills, leaks or releases, which change from 
region to region.
Distilled Coconut Fatty Acid
Brenntag Canada Inc.
Date of Revision:
2008 June 25
WHMIS Number :
00064740
Page 3 of 6
In all cases of leak or spill contact vendor at Emergency Number shown on the front page of this MSDS. 
Wear protective clothing. Recover spilled material on non-combustible absorbents, such as sand or 
vermiculite, and place in covered containers for disposal. Collect product for recovery or disposal.  For 
release to land, or storm water runoff, contain discharge by constructing dykes or applying inert 
absorbent;  for release to water, utilize damming and/or water diversion to minimize the spread of 
contamination.  Ventilate enclosed spaces.  Notify applicable government authority if release is 
reportable or could adversely affect the environment.
Containment and Clean-Up 
Procedures:
7. HANDLING AND STORAGE
HANDLING
Use normal "good" industrial hygiene and housekeeping practices. Containers exposed to heat may be 
under internal pressure.  These should be cooled and carefully vented before opening.  A face shield 
and apron should be worn.
Handling Practices:
See Section 8, "Engineering Controls".
Ventilation Requirements:
Use only with adequate ventilation and avoid breathing aerosols ( vapours or mists ). Avoid contact with 
eyes, skin or clothing.  Wash thoroughly with soap and water after handling.  Wash contaminated 
clothing thoroughly before re-use. Do not use cutting or welding torches on empty drums that contained 
this material/product.
Other Precautions:
STORAGE
See below.
Storage Temperature (°C):
General exhaust is acceptable.
Ventilation Requirements:
Store in a cool, well-ventilated area.  Keep away from heat, sparks and flames.  Keep containers 
closed.  Do not expose sealed containers to temperatures above 40° C. Keep containers closed.
Storage Requirements:
Confirm suitability of any material before using.
Special Materials to be Used for 
Packaging or Containers:
8. EXPOSURE CONTROLS / PERSONAL PROTECTION
Recommendations listed in this section indicate the type of equipment, which will provide protection against overexposure to this 
product.  Conditions of use, adequacy of engineering or other control measures, and actual exposures will dictate the need for specific 
protective devices at your workplace.
ENGINEERING CONTROLS
General exhaust is acceptable. Local exhaust ventilation preferred. Make up air should be supplied to 
balance air that is removed by local or general exhaust ventilation. Ventilate low lying areas such as 
sumps or pits where dense vapours may collect.
Engineering Controls:
PERSONAL PROTECTIVE 
EQUIPMENT (PPE)
Safety glasses with side shields are recommended to prevent eye contact. Use chemical safety goggles 
when there is potential for eye contact. Contact lenses should not be worn when working with this 
material.
Eye Protection:
Gloves and protective clothing made from PVC should be impervious under conditions of use.   Prior to 
use, user should confirm impermeability. Discard contaminated gloves.
Skin Protection:
No specific guidelines available. A NIOSH/MSHA-approved air-purifying respirator equipped with 
organic vapour cartridges for concentrations up to 50 mg/m3 oil mist. An air-supplied respirator if 
concentrations are higher or unknown.
If while wearing a respiratory protection, you can smell, taste or otherwise detect anything unusual, or in 
the case of a full facepiece respirator you experience eye irritation, leave the area immediately.  Check 
to make sure the respirator to face seal is still good.  If it is, replace the filter, cartridge or canister.  If 
the seal is no longer good, you may need a new respirator.  (4)
Respiratory Protection:
Wear regular work clothing. The use of coveralls is recommended. Locate safety shower and eyewash 
station close to chemical handling area. Take all precautions to avoid personal contact.
Other Personal Protective 
Equipment:
None established for this product.
EXPOSURE GUIDELINES
9. PHYSICAL AND CHEMICAL PROPERTIES  (Not intended as Specifications)
Distilled Coconut Fatty Acid
Brenntag Canada Inc.
Date of Revision:
2008 June 25
WHMIS Number :
00064740
Page 4 of 6
Paste.
Light yellow semi-solid.
Sweet coconut smell.
Not available.
160 at 6 mm.  (3)
22 - 26.  (3)
100.  (3)
Not available.
0.89.
Not available.
Not available.
Not available.
Not soluble in water.
Not available.
Not available.
Not available.
Not available.
Physical State:
Appearance:
Odour:
Odour Threshold (ppm):
Boiling Range (°C):
Melting/Freezing Point (°C):
Vapour Pressure (mm Hg at 20° C):
Vapour Density (Air = 1.0):
Relative Density (g/cc):
Bulk Density:
Viscosity:
Evaporation Rate (Butyl Acetate = 1.0):
Solubility:
% Volatile by Volume:
pH:
Coefficient of Water/Oil Distribution:
Volatile Organic Compounds (VOC):
157.  (3)
Flashpoint (°C):
11. TOXICOLOGICAL INFORMATION
TOXICOLOGICAL DATA:
SUBSTANCE
LD50 (Oral, Rat)
LD50 (Dermal, Rabbit)
LC50 (Inhalation, Rat, 4h)
Fatty Acids, coco
18 500 mg/kg (3)
--- 
--- 
The ingredient(s) of this product is (are) not classed as carcinogenic by ACGIH, IARC, OSHA or NTP.
Carcinogenicity Data:
No adverse reproductive effects are anticipated.
Reproductive Data:
No adverse mutagenic effects are anticipated.
Mutagenicity Data:
No adverse teratogenic effects are anticipated.
Teratogenicity Data:
None known.
Respiratory / Skin Sensitization 
Data:
None known.
Synergistic Materials:
None known.
Other Studies Relevant to 
Material:
12. ECOLOGICAL INFORMATION
Not available. Ecotoxicity is expected to be low based on the low water solubility.
Ecotoxicity:
10. STABILITY AND REACTIVITY
CHEMICAL STABILITY
Stable.
Under Normal Conditions:
Not flammable.
Under Fire Conditions:
Will not occur.
Hazardous Polymerization:
Temperatures above 165 °C. Keep tightly closed to protect quality.
Conditions to Avoid:
Strong oxidizing and reducing agents. Lewis or mineral acids. Strong bases.
Materials to Avoid:
Thermal decomposition products are toxic and may include oxides of and irritating gases.
Decomposition or Combustion 
Products:
Distilled Coconut Fatty Acid
Brenntag Canada Inc.
Date of Revision:
2008 June 25
WHMIS Number :
00064740
Page 5 of 6
Not available. May be hazardous if allowed to enter drinking water intakes. Product has an unaesthetic 
appearance and can be a nuisance. Do not contaminate domestic or irrigation water supplies, lakes, 
streams, ponds, or rivers.
Environmental Fate:
13. DISPOSAL CONSIDERATIONS
None required.
Deactivating Chemicals:
This information applies to the material as manufactured. Reevaluation of the product may be required 
by the user at the time of disposal since the product uses, transformations, mixtures and processes 
may influence waste classification. Dispose of waste material at an approved (hazardous) waste 
treatment/disposal facility in accordance with applicable local, provincial and federal regulations.  Do not 
dispose of waste with normal garbage, or to sewer systems.
Waste Disposal Methods:
See "Waste Disposal Methods".
Safe Handling of Residues:
Empty containers retain product residue. Empty drums should be completely drained, properly bunged 
and promptly returned to a drum reconditioner. Dispose of waste material at an approved (hazardous) 
waste treatment/disposal facility or waste incineration facility in accordance with applicable local, 
provincial and federal regulations.
Disposal of Packaging:
14. TRANSPORTATION INFORMATION
CANADIAN TDG ACT SHIPPING DESCRIPTION:
This product is not regulated by TDG.
Label(s):  Not applicable.          Placard:  Not applicable.
ERAP Index: -----.
Exemptions: None known.
US DOT CLASSIFICATION (49CFR 172.101, 172.102):
This product is not regulated by DOT.
Label(s):  Not applicable.          Placard:  Not applicable.
CERCLA-RQ: Not available.
Exemptions: None known.
15. REGULATORY INFORMATION
CANADA
All constituents of this product are included on the DSL.
CEPA - NSNR:
Not included.
CEPA - NPRI:
Controlled Products Regulations Classification (WHMIS):
D-2B:  Toxic (skin and eye irritant)
USA
All constituents of this product are included on the TSCA inventory.
Environmental Protection Act:
Skin and Eye Irritant.
OSHA HCS (29CFR 1910.1200):
Text22:
NFPA:  2 Health,   1 Fire,   0 Reactivity   (3)
Text22:
HMIS:  2 Health,   1 Fire,   0 Reactivity   (3)
INTERNATIONAL
Not available.
16.  OTHER INFORMATION
REFERENCES
RTECS-Registry of Toxic Effects of Chemical Substances, Canadian Centre for Occupational Health and Safety RTECS 
database.
1.
Clayton, G.D. and Clayton, F.E., Eds., Patty's Industrial Hygiene and Toxicology, 3rd ed., Vol. IIA,B,C, John Wiley and Sons, 
New York, 1981.
2.
Distilled Coconut Fatty Acid
Brenntag Canada Inc.
Date of Revision:
2008 June 25
WHMIS Number :
00064740
Page 6 of 6
Supplier's Material Safety Data Sheet(s).
3.
CHEMINFO, through "CCINFOdisc", Canadian Centre for Occupational Health and Safety, Hamilton, Ontario, Canada.
4.
Guide to Occupational Exposure Values, 2007, American Conference of Governmental Industrial Hygienists, Cincinnati, 2007.
5.
Regulatory Affairs Group, Brenntag Canada Inc.
6.
The British Columbia Drug and Poison Information Centre, Poison Managements Manual, Canadian Pharmaceutical 
Association, Ottawa, 1981.
7.
____________________________________________________________________________________________________________
The information contained herein is offered only as a guide to the handling of this specific material and has been prepared in good faith 
by technically knowledgeable personnel.  It is not intended to be all-inclusive and the manner and conditions of use and handling may 
involve other and additional considerations.  No warranty of any kind is given or implied and Brenntag Canada Inc. will not be liable for 
any damages, losses, injuries or consequential damages which may result from the use of or reliance on any information contained 
herein.  This Material Safety Data Sheet is valid for three years.
____________________________________________________________________________________________________________
To obtain revised copies of this or other Material Safety Data Sheets, contact your nearest Brenntag Canada Regional office.
British Columbia:  20333-102B Avenue, Langley, BC, V1M 3H1
         Phone:  (604) 513-9009         Facsimile:  (604) 513-9010
Alberta:   6628 - 45 th. Street, Leduc, AB, T9E 7C9
         Phone:  (780) 986-4544         Facsimile:  (780) 986-1070
Manitoba:  681 Plinquet Street, Winnipeg, MB, R2J 2X2
         Phone:  (204) 233-3416         Facsimile:  (204) 233-7005
Ontario:  43 Jutland Road, Toronto, ON, M8Z 2G6
         Phone:  (416) 259-8231         Facsimile:  (416) 259-5333
Quebec:  2900 Jean Baptiste Des., Lachine, PQ, H8T 1C8
         Phone:  (514) 636-9230         Facsimile:  (514) 636-0877
Atlantic:  A-105 Akerley Boulevard, Dartmouth, NS, B3B 1R7
         Phone:  (902) 468-9690         Facsimile:  (902) 468-3085
____________________________________________________________________________________________________________
Prepared By:  Regulatory Affairs Group, Brenntag Canada Inc., (416) 259-8231.
</p>