Build an electric Scoot-car Designed by R O B E R T W O O L S O N Here's a sidewalk special for young hot rodders that safely takes the corner on two wheels, has two forward speed and brakes that stop on a dime This is the parallel-arm steering gear being placed in position. Pivot links are bolted to the deck, using washers and lockouts • ONE FULL BATTERY CHARGE readies Scoot- car for hours of fun. Cornering wheels, one on each side of the chassis, give the driver sure stability from a standing start, and a near top speed of 10 to 12 miles per hour puts the car up on two wheels where it steers and controls like a car, but rides like a speedy low-slung scooter. When cornering, the car leans over on one or the other of the outrider wheels, enabling the driver to keep safe, full control when turning. Power and brake application are controlled by pedals with strong return springs. Release the power pedal, hit the brake hard and Scoot-car stops within its length of 4 ft. Caution: While Scoot-car is a safe toy 513 1. Taillight (optional) 2. Taillight bracket 3. Rear fender 4. Seat 5. Steering wheel 6. Front-fender trim (1/2"x1/2") 7. Front lender 8. Steering post, 1/2" x 25" rod 9. Shaft collar, 1/2" dia. 10. Lower bearing, steering post 11 Steering arm 12. Cable bracket 13. Drive pedal 14. Turnbuckle 15. Drive and brake cables 16. T-hinge. 3" leaf 17. Tie rod, 1/4" steel rod 18. Steering limit bracket. 1/8" x 1" flat steel 19. Roller-race mounting block.. 1/2" x 1" x 6" hardwood 20. Roller race 21. Steering link 22. Bell crank 23. Roller, 1/2" shaft collar 24: Wheel spindle. 1/2" x 11" rod 25; Semipneumalic wheel. 12 x 3:00 26. Steering parallel 27. Steering pivot link 28. Battery cradle 29. Cradle shim. 1/4" hardboard 30. Corrugated rubber mats 31 . Battery cable 32. Plywood chassis 33. Brake band, 1/2" V-belt 34. Bumper. 1/2" thin-wall conduit 35. Motor-mounting bracket 36. Crutch tip 37. Ground-strap bracket 38. Motor terminal strap 39. Motor (auto starter) 40. Rear-fender brackets 41. Rear-fender support 42. Battery cradle 43. Battery cable 44. Fender bracket 45. Fender brace 48. Semipneumatic wheal, 6 x 1:50 47. Wheel bracket 48. Chassis cross brace 49. Control rod (pedal to switch) 50. Drive and brake cables 51. Return spring 52. Spring bracket 53. Bumper bracket 54. Roller-race assembly .55- power-cable lover 56. Roller-shaft bearings (hardwood) 57. Brake rocker, 1/8" x 1" steel 58. Cable clamp 59. S-hook, steel rod 60. 12-tooth drive sprocket 61 . Roller chain 62. 52-tooth sprooket 63. Spacer, 4" V-pulley 64. Same as part # 25 65. Same as part # 24. except 9VV 66. See part keyed #33 67. V-pulley. 6". brake drum 68. Return spring 69. Drive-wheel bearings 70. Brake rocker shaft, 1/2" x 4-3/4"" steel shafting 71. Insulator. 1/8" hardboard 72. Compression spring 73. .Sliding contact arm, 74. Carbon resistor 75. Resistor brackets 76. Retainer (large washer) ci /: mechanically, there are precautions to observe ;n riding. When operating it for the first time, the immediate reaction to tipping is to take the feet off the pedals and plant them on the ground. With the car in motion, this can pitch the rider forward. The outrider wheels, of course, make lipping over impossible, and after a few trial spins, the rider will overcome the tendency to brace himself and will keep his feet on the pedals. Looking over the details you will see that Scoot-car has a unique parallel-arm steering gear and a positive roller-chain drive from an auto- starter motor. Throughout the construction, full use is made of standard, readily available parts ;md materials wherever possible. For example, the steering wheel is a 1.0-in.-diameter spoked V-pulley, wrapped with electrician's tape over a length of hose set into the V-rim of the pulley. The roller-chain assures positive drive from the motor to the ground wheel. Slack In the chain should not exceed 1/2 in. Note the position of the battery cables and of the ground and power straps on the board 517 The brake cable is attached to the brake rocker with a cable eye and clamp. Note the end of the brake band bolted into a loop and attached to an S-hook This makes a neat, attractive wheel of just the right size. Make the plywood chassis (part No. 32) first, cutting the three openings for front and rear wheels and battery cradle as the first step. These openings should be cut just inside the pattern lines and then smoothed out to the lines with a wood rasp. Round corners slightly and sand smooth. Round the corners of the chassis to the radius indicated and sand all edges. Then lay out the hole pattern and centermark the location of holes with an awl. All smaller holes indicated are 1/4 in. in diameter. Those for the battery-cradle studs are 3/8 in. in diameter to take 3/8-in. threaded rod. Holes taking the rear-wheel bear- ing bolts are 5/16 in. in diameter and the two largest holes indicated take the battery cable and motor-terminal strap and are each 3/4 in. in di- The free end of the V-belt brake band is bent back on itself to form a loop taking one eye of an S-hook. The loop is secured by two bolts ameter. The two holes, indicated as elongated, take the brake and power-control cables and are drilled 1/4 in. in diameter and at as steep an angle as possible, then enlarged with a round file so that the cables clear without binding. Next comes installation of front and rear wheels. Take the front wheel first and begin by noting closely the relationship of the parts. The parallels and the pivot links arc of flat steel (also often referred to as band iron) and are cut to length and drilled as detailed. The front wheel is centered on its spindle with shaft collars, and the outer ends of the spindle are carried on roll- ers, which are 1/2-in. shaft collars cotter-pinned on the shaft. The spindle is drilled just inside the collars (rollers) to take the 1/4 -in. capscrews which hold the parallels to the shaft. One screw is longer to take the steering link. Spacer washers 518 are placed between the joining parts and all screws carry additional washers and locknuts to permit free movement. In the assembly, the rollers on the ends of the wheel spindle ride on races made as shown. Each consists of a mount- ing block of hardwood and a facing of flat steel, and the two units are attached to the underside of the deck with wood screws. The pivot links are bolted to the underside of the deck and the steer- ing, or connecting, link attaches to the bell crank. The latter is bolted to the underside of the chassis and the free arm takes the lower end of the tie rod when assembled. The upper end of the tie rod is attached to the steering arm on the lower end of the steering post. The steering arm is riv- eted to a shaft collar which provides a hub and a means of attaching to the steering post. rear wheel attached next Now comes the rear wheel which is attached to the deck with two pillow-block bearings and carries the driven sprocket and brake drum. No- tice especially the rear-wheel assembly. The brake drum is a V-pulley which slips onto the wheel spindle to which it is locked with its set- screw and additionally locked by a capscrew long enough to permit the threaded end to enter a hole drilled in the hub of the rear wheel. On the opposite side of the wheel a smaller V-pulley, with the rim cut away as indicated, serves as a spacer and a hub for the driven sprocket. It is locked to the hub of the rear wheel in the same manner as the brake drum. The brake band is a length of 1/2-in. V-belt, one end of which is attached to the top face of the deck with two wood screws. The other end is doubled back on itself to form a loop around an S-hook, the latter attaching to the brake arm. The brake rocker is carried on a shaft sup- ported in hardwood bearings bolted to the un- derside of the deck. The brake-return spring at- taches to the long arm of the rocker and to one of the pillow-block bearing bolts. The second S-hook attaches to the long arm of the rocker and to a cable eye which connects to the 3/16-in. wire cable from the brake pedal. Note that turn- buckles are provided on both brake and power cables for adjustment. The power-control cable reaches from the turnbuckle to one end of a pivoted lever. The other end of the lever connects to the control rod, part No. 49. The free end of the control rod is bent at right angles, drilled and cotterpinned to the sliding contact, part No. 73. The lever is returned by a spring, one end of which is hooked The lower half of the battery cradle or carrier is held in place by jam nuts. Be sure the nuts are tight Turnbuckles provide adjustment on both the power and the brake cables to a bracket screwed to the underside of the deck, see parts No. 51 and 52. The resistor, which is the carbon core from a dry cell, is mounted in brackets, parts No. 74 and 75, and is drilled and tapped for three 1/4-in. flat-head screws and two 1/4-in. capscrews, the latter holding it in place between the brackets. Drilling and tapping must be done with care, the tap holes being drilled slightly oversize so that the tap cuts only a 50- to 60-percent thread. One screw of the three shown takes the end of the battery cables, the other two, which are contacts through the resistor, are fitted with squares cut from 1/16 x 1/2- in. flat steel and center-countersunk to take the heads of the screws flush. In the off position the spring-loaded sliding contact arm contacts an in- sulating strip of hardboard, part No. 71, which is attached to the ground strap. This type of switch (in effect a rheostat) prevents heavy current surges and reduces arcing in the control switch to the minimum. The motor-mounting brackets are made right and left and are so placed that the regular 519 build a Scoot-car, continued mounting lugs on the motor can be utilized as fastenings. Note especially how the aluminum ground strap from the motor terminal is bent so that it passes through the large hole in the chassis, the lower end being held in place by the bolt on which the sliding contact pivots. It will be noted that there is an L-shaped retainer attached to one of the brackets supporting the resistor. This has been lowered in the photo for clarity. It has, however, been replaced by a large washer, part No. 76. This retainer prevents the insulator, part No. 71, from swinging. All parts of the seat except the risers are made from 3/8-in. plywood and all parts are joined with 1 x 1 x 1/2-in. steel corner angles which are readily available. Care must be taken when lo- cating the front and side risers to see that the holes in the attaching corner angles register with those in the deck to which the seat is attached with bolts and wing nuts. Note also that the inner end of the rear fender is attached to the back of the seat with corner angles, small bolts and wing nuts. The front fender is bracketed and braced to the deck and serves not only as a front-wheel fender, but also as a support for the steering post, or column. The brake and power pedals consist of a 3-in. T-hinge and a pedal, or pad, of plywood, and a bracket which takes one eye of the turnbuckles. The hinge leaves are attached to the deck with wood screws. The bumper is a length of 1/2-in. thin-wall con- duit and is held in place with six flat-steel brack- ets screwed to the underside of the platform with wood screws and to the thin-wall conduit with self-tapping screws or sheet-metal screws. Rubber crutch tips are slipped on the open rear ends of the bumper. It may be attached either before or after the cornering wheels are in place. These wheels are carried at an angle of 15 deg. on heavy outrigger brackets bolted to the deck. Finally, install the steel-angle brace. All that remains are installation of the battery cradle, the 6-v. battery and the foot and seat mats which are cut from corrugated-rubber stair treads and cemented to the deck. The taillight can be of the type pictured and detailed and wired into the power circuit, or you can use a battery-powered bike headlight and cover the lens with red cellophane. Also, you'll probably need to do some adjusting of the brake and power-cable turnbuckles to get the controls working right. 520