Loading ...
Global Do...
Science
MSDS
385
26
Try Now
Log In
Pricing
<p>MATERIAL SAFETY DATA SHEET BRENNSOFT ES2 / ES2-HV 3. HAZARDS IDENTIFICATION Harmful if inhaled, absorbed through skin, or swallowed. Causes severe skin and eye irritation. Vapours are irritating to eyes and respiratory tract. See "Other Health Effects" Section. Can decompose at high temperatures forming toxic gases. Contents may develop pressure on prolonged exposure to heat. EMERGENCY OVERVIEW: POTENTIAL HEALTH EFFECTS Excessive contact with mist or spray may cause irritation of mucous membranes, coughing and difficulty in breathing. See "Other Health Effects" Section. Inhalation: Brief contact causes irritation (itching, local redness or possible swelling). This product may cause symptoms of skin irritation such as reddening, swelling, rash, scaling, or blistering. May cause defatting, drying and cracking of the skin. Prolonged and repeated contact may lead to dermatitis. Skin Contact: A single, prolonged skin exposure is not likely to result in the absorption of toxic amounts of the material. Skin Absorption: Causes severe eye irritation. This product causes irritation, redness and pain. Eye Contact: EMERGENCY TELEPHONE NUMBERS (FOR EMERGENCIES INVOLVING CHEMICAL SPILLS OR RELEASE) Toronto, ON (416) 226-6117 Montreal, QC (514) 861-1211 Winnipeg, MB (204) 943-8827 Edmonton, AB (780) 424-1754 Calgary, AB (403) 263-8660 Vancouver, BC (604) 685-5036 1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION Brenntag Canada Inc. 43 Jutland Rd. Toronto, ON M8Z 2G6 (416) 259-8231 Website: http:\\www.brenntag.ca WHMIS#: 00065593 Index: 2006 December 07 PRODUCT IDENTIFICATION Brennsoft ES2 / ES2-HV. Product Name: 2006 December 07 Date of Revision: Effective Date: HCI4733/06D Sodium Lauryl Ether Sulphate. Chemical Name: Brennsoft ES2 ; Brennsoft ES-HV ; Brennsoft ES2-4000; Sodium alkyl ether sulphate; Sodium Laureth Sulphate. Synonyms: Anionic surfactant. Chemical Family: Not available. Molecular Formula: Manufacture of soaps. Shampoos and detergents. Surfactant. Foaming Agent. Cosmetics. Product Use: WHMIS Classification / Symbol: READ THE ENTIRE MSDS FOR THE COMPLETE HAZARD EVALUATION OF THIS PRODUCT. D-2B: Toxic (skin and eye irritant) Ingredient CAS# ACGIH TLV % Concentration 2. COMPOSITION, INFORMATION ON INGREDIENTS (Not Intended As Specifications) Sodium Laureth Sulphate 68585-34-2 --- 15-40 Brennsoft ES2 / ES2-HV Brenntag Canada Inc. Date of Revision: 2006 December 07 WHMIS Number : 00065593 Page 2 of 6 4. FIRST AID MEASURES FIRST AID PROCEDURES Move victim to fresh air. Give artificial respiration ONLY if breathing has stopped. Give cardiopulmonary resuscitation (CPR) if there is no breathing AND no pulse. Obtain medical attention IMMEDIATELY. Inhalation: Start flushing while removing contaminated clothing. Wash affected areas thoroughly with soap and water. If irritation, redness, or a burning sensation develops and persists, repeat flushing and obtain medical attention. Skin Contact: Immediately flush eyes thoroughly for 5 minutes with running water. Hold eyelids open during flushing. If irritation persists, repeat flushing. Obtain medical attention. Eye Contact: Do not attempt to give anything by mouth to an unconscious person. If victim is alert and not convulsing, rinse mouth out and give 1/2 to 1 glass of water to dilute material. DO NOT induce vomiting. If spontaneous vomiting occurs, have victim lean forward with head down to avoid breathing in of vomitus, rinse mouth and administer more water. Obtain medical attention IMMEDIATELY. Ingestion: This product contains materials that may cause severe pneumonitis if aspirated. If ingestion has occurred less than 2 hours earlier, carry out careful gastric lavage; use endotracheal cuff if available, to prevent aspiration. Observe patient for respiratory difficulty from aspiration pneumonitis. Give artificial resuscitation and appropriate chemotherapy if respiration is depressed. Medical conditions that may be aggravated by exposure to this product include diseases of the skin, eyes or respiratory tract. Note to Physicians: This product may cause mild gastrointestinal discomfort. Ingestion of large amounts may cause nausea, gastrointestinal upset and abdominal pain. Ingestion: Effects (irritancy) on the skin and eyes may be delayed, and damage may occur without the sensation or onset of pain. Strict adherence to first aid measures following any exposure is essential. Other Health Effects: 5. FIRE-FIGHTING MEASURES Flashpoint (°C) AutoIgnition Temperature (°C) LEL UEL Flammability Limits in Air (%): > 93.3 Not applicable. Not applicable. Not applicable. Not regulated. Flammability Class (WHMIS): Thermal decomposition products are toxic and may include oxides of sulphur, sodium, carbon and irritating gases. Hazardous Combustion Products: Closed containers exposed to heat may burst. Spilled material may cause floors and contact surfaces to become slippery. Not normally a fire hazard. Water content of product prevents ignition. Unusual Fire or Explosion Hazards: Not expected to be sensitive to mechanical impact. Sensitivity to Mechanical Impact: Not available. Rate of Burning: Not available. Explosive Power: Not expected to be sensitive to static discharge. Sensitivity to Static Discharge: EXTINGUISHING MEDIA Foam. Use carbon dioxide or dry chemical media for small fires. If only water is available, use it in the form of a fog. Do not use high volume water jet. Fire Extinguishing Media: FIRE FIGHTING INSTRUCTIONS Isolate materials that are not involved in the fire and protect personnel. Cool containers with flooding quantities of water until well after the fire is out. Instructions to the Fire Fighters: Use self-contained breathing apparatus and protective clothing. Fire Fighting Protective Equipment: 6. ACCIDENTAL RELEASE MEASURES Information in this section is for responding to spills, leaks or releases in order to prevent or minimize the adverse effects on persons, Brennsoft ES2 / ES2-HV Brenntag Canada Inc. Date of Revision: 2006 December 07 WHMIS Number : 00065593 Page 3 of 6 property and the environment. There may be specific reporting requirements associated with spills, leaks or releases, which change from region to region. In all cases of leak or spill contact vendor at Emergency Number shown on the front page of this MSDS. Wear protective clothing. Collect product for recovery or disposal. For release to land, or storm water runoff, contain discharge by constructing dykes or applying inert absorbent; for release to water, utilize damming and/or water diversion to minimize the spread of contamination. Ventilate enclosed spaces. Notify applicable government authority if release is reportable or could adversely affect the environment. Containment and Clean-Up Procedures: 7. HANDLING AND STORAGE HANDLING Use normal "good" industrial hygiene and housekeeping practices. Containers exposed to heat may be under internal pressure. These should be cooled and carefully vented before opening. A face shield and apron should be worn. Do not use pressure to empty containers. Handling Practices: See Section 8, "Engineering Controls". Ventilation Requirements: Use only with adequate ventilation and avoid breathing aerosols ( vapours or mists ). Avoid contact with eyes, skin or clothing. Wash thoroughly with soap and water after handling. Wash contaminated clothing thoroughly before re-use. Other Precautions: STORAGE Ideal storage temperature is 15 to 30 °C. Do not store above 40 °C. (3) Storage Temperature (°C): General exhaust is acceptable. Ventilation should be corrosion proof. Ventilation Requirements: Store in a cool, well-ventilated area. Keep away from heat, sparks and flames. Keep containers closed. Do not expose sealed containers to temperatures above 40° C. Avoid freezing! Protect from direct sunlight. Protect against physical damage. Storage Requirements: Confirm suitability of any material before using. Special Materials to be Used for Packaging or Containers: 8. EXPOSURE CONTROLS / PERSONAL PROTECTION Recommendations listed in this section indicate the type of equipment, which will provide protection against overexposure to this product. Conditions of use, adequacy of engineering or other control measures, and actual exposures will dictate the need for specific protective devices at your workplace. ENGINEERING CONTROLS General exhaust is acceptable. Local exhaust ventilation preferred. Ventilation should be corrosion proof. Make up air should be supplied to balance air that is removed by local or general exhaust ventilation. Ventilate low lying areas such as sumps or pits where dense vapours may collect. Engineering Controls: PERSONAL PROTECTIVE EQUIPMENT (PPE) Safety glasses with side shields are recommended to prevent eye contact. Use chemical safety goggles when there is potential for eye contact. Contact lenses should not be worn when working with this material. Eye Protection: Gloves and protective clothing made from rubber or plastic should be impervious under conditions of use. Prior to use, user should confirm impermeability. Discard contaminated gloves. Skin Protection: No specific guidelines available. Respiratory protection should not be necessary unless the material is heated or a mist created. A NIOSH/MSHA-approved air-purifying respirator equipped with dust, mist, fume and organic vapour cartridges for concentrations up to 1 000 ppm. Use an air-supplied respirator if concentrations are high or unknown. If while wearing a respiratory protection, you can smell, taste or otherwise detect anything unusual, or in the case of a full facepiece respirator you experience eye irritation, leave the area immediately. Check to make sure the respirator to face seal is still good. If it is, replace the filter, cartridge or canister. If the seal is no longer good, you may need a new respirator. (4) Respiratory Protection: Wear regular work clothing. The use of coveralls is recommended. Locate safety shower and eyewash station close to chemical handling area. Take all precautions to avoid personal contact. Other Personal Protective Equipment: None established for this product. EXPOSURE GUIDELINES Brennsoft ES2 / ES2-HV Brenntag Canada Inc. Date of Revision: 2006 December 07 WHMIS Number : 00065593 Page 4 of 6 Liquid. Water-white liquid or paste. Characteristic odour. Not available. Not available. Not available. Not available. Not available. 1.0 - 1.1 1000 - 1100 kg/m3 Not available. Not available. Soluble in water. Not available. 7 - 9. Not available. Not available. Physical State: Appearance: Odour: Odour Threshold (ppm): Boiling Range (°C): Melting/Freezing Point (°C): Vapour Pressure (mm Hg at 20° C): Vapour Density (Air = 1.0): Relative Density (g/cc): Bulk Density: Viscosity: Evaporation Rate (Butyl Acetate = 1.0): Solubility: % Volatile by Volume: pH: Coefficient of Water/Oil Distribution: Volatile Organic Compounds (VOC): 9. PHYSICAL AND CHEMICAL PROPERTIES (Not intended as Specifications) 11. TOXICOLOGICAL INFORMATION TOXICOLOGICAL DATA: SUBSTANCE LD50 (Oral, Rat) LD50 (Dermal, Rabbit) LC50 (Inhalation, Rat, 4h) Sodium Laureth Sulphate 1 600 - 1 800 mg/kg (3) --- --- The ingredient(s) of this product is (are) not classed as carcinogenic by ACGIH, IARC, OSHA or NTP. Carcinogenicity Data: No adverse reproductive effects are anticipated. Reproductive Data: No adverse mutagenic effects are anticipated. Mutagenicity Data: No adverse teratogenic effects are anticipated. Teratogenicity Data: None known. Respiratory / Skin Sensitization Data: None known. Synergistic Materials: None known. Other Studies Relevant to Material: 12. ECOLOGICAL INFORMATION May be harmful to aquatic life. Ecotoxicity: 10. STABILITY AND REACTIVITY CHEMICAL STABILITY Stable. Under Normal Conditions: Not flammable. Not normally a fire hazard. Water content of product prevents ignition. Under Fire Conditions: Will not occur. Hazardous Polymerization: High temperatures, sparks, open flames and all other sources of ignition. Temperatures above 40 °C. (3) Keep tightly closed to protect quality. Conditions to Avoid: Strong oxidizers. Cationic components (surfactant or dyes). Lewis or mineral acids. Materials to Avoid: Thermal decomposition products are toxic and may include oxides of sulphur, sodium, carbon and irritating gases. Decomposition or Combustion Products: Brennsoft ES2 / ES2-HV Brenntag Canada Inc. Date of Revision: 2006 December 07 WHMIS Number : 00065593 Page 5 of 6 Can be dangerous if allowed to enter drinking water intakes. Do not contaminate domestic or irrigation water supplies, lakes, streams, ponds, or rivers. Environmental Fate: 13. DISPOSAL CONSIDERATIONS Recover spilled material on adsorbents, such as sand or vermiculite, and place in covered containers for disposal. Deactivating Chemicals: This information applies to the material as manufactured. Reevaluation of the product may be required by the user at the time of disposal since the product uses, transformations, mixtures and processes may influence waste classification. Dispose of waste material at an approved (hazardous) waste treatment/disposal facility in accordance with applicable local, provincial and federal regulations. Do not dispose of waste with normal garbage, or to sewer systems. Waste Disposal Methods: See "Waste Disposal Methods". Safe Handling of Residues: Empty containers retain product residue (liquid and/or vapour) and can be dangerous. Empty drums should be completely drained, properly bunged and promptly returned to a drum reconditioner. Treat package in the same manner as the product. Disposal of Packaging: 14. TRANSPORTATION INFORMATION CANADIAN TDG ACT SHIPPING DESCRIPTION: This product is not regulated by TDG. Label(s): Not applicable. Placard: Not applicable. ERAP Index: -----. Exemptions: None known. US DOT CLASSIFICATION (49CFR 172.101, 172.102): This product is not regulated by DOT. Label(s): Not applicable. Placard: Not applicable. CERCLA-RQ: Not available. Exemptions: None known. 15. REGULATORY INFORMATION CANADA All constituents of this product are included on the DSL. CEPA - NSNR: Not included. CEPA - NPRI: Controlled Products Regulations Classification (WHMIS): D-2B: Toxic (skin and eye irritant) USA All constituents of this product are included on the TSCA inventory. Environmental Protection Act: Skin and Eye Irritant. OSHA HCS (29CFR 1910.1200): Text22: NFPA: Health, Fire, Reactivity (Not available.) Text22: HMIS: Health, Fire, Reactivity (Not available.) INTERNATIONAL Not available. 16. OTHER INFORMATION REFERENCES RTECS-Registry of Toxic Effects of Chemical Substances, Canadian Centre for Occupational Health and Safety RTECS database. 1. Clayton, G.D. and Clayton, F.E., Eds., Patty's Industrial Hygiene and Toxicology, 3rd ed., Vol. IIA,B,C, John Wiley and Sons, New York, 1981. 2. Supplier's Material Safety Data Sheet(s). 3. Brennsoft ES2 / ES2-HV Brenntag Canada Inc. Date of Revision: 2006 December 07 WHMIS Number : 00065593 Page 6 of 6 CHEMINFO, through "CCINFOdisc", Canadian Centre for Occupational Health and Safety, Hamilton, Ontario, Canada. 4. Guide to Occupational Exposure Values, 2007, American Conference of Governmental Industrial Hygienists, Cincinnati, 2007. 5. Regulatory Affairs Group, Brenntag Canada Inc. 6. The British Columbia Drug and Poison Information Centre, Poison Managements Manual, Canadian Pharmaceutical Association, Ottawa, 1981. 7. ____________________________________________________________________________________________________________ The information contained herein is offered only as a guide to the handling of this specific material and has been prepared in good faith by technically knowledgeable personnel. It is not intended to be all-inclusive and the manner and conditions of use and handling may involve other and additional considerations. No warranty of any kind is given or implied and Brenntag Canada Inc. will not be liable for any damages, losses, injuries or consequential damages which may result from the use of or reliance on any information contained herein. This Material Safety Data Sheet is valid for three years. ____________________________________________________________________________________________________________ To obtain revised copies of this or other Material Safety Data Sheets, contact your nearest Brenntag Canada Regional office. British Columbia: 20333-102B Avenue, Langley, BC, V1M 3H1 Phone: (604) 513-9009 Facsimile: (604) 513-9010 Alberta: 6628 - 45 th. Street, Leduc, AB, T9E 7C9 Phone: (780) 986-4544 Facsimile: (780) 986-1070 Manitoba: 681 Plinquet Street, Winnipeg, MB, R2J 2X2 Phone: (204) 233-3416 Facsimile: (204) 233-7005 Ontario: 43 Jutland Road, Toronto, ON, M8Z 2G6 Phone: (416) 259-8231 Facsimile: (416) 259-5333 Quebec: 2900 Jean Baptiste Des., Lachine, PQ, H8T 1C8 Phone: (514) 636-9230 Facsimile: (514) 636-0877 Atlantic: A-105 Akerley Boulevard, Dartmouth, NS, B3B 1R7 Phone: (902) 468-9690 Facsimile: (902) 468-3085 ____________________________________________________________________________________________________________ Prepared By: Regulatory Affairs Group, Brenntag Canada Inc., (416) 259-8231. </p>