Telephone entry/access control system © 2006 The Chamberlain Group, Inc. All Rights Reserved ® ™ ® Installation Manual for EL MODELS Table of Contents Page 1 Mounting the Unit Page Dimensions 2 EL25 Installation 3 Rotating the Keypad for Vertical Mounting 3 Unlocking/Locking EL2000 4 EL2000 Installation 5 Wire Type Wire Connections to Unit (Factory Settings for Relays) 6 Wire Specs and Run Distances 7 Power Wire Specs and Run Distances 7 Grounding the Unit Grounding the Unit 8 Phone Lines Wiring 1 Unit to Telco Line 9 Wiring Multiple Units to Telco Line 10 Wiring with No Telco Line 11 Wiring to Dedicated Telco Line 12 Wiring to an Internal Phone System 13 Connection to an NPBI System 14 External Devices Wiring a Door Strike Lock 15 Wiring a Maglock 15 Wiring a Gate Operator 16 Wiring a Key Switch/PIR/REX 16 Wiring a Door Sensing Device 17 Wiring the AutoCall Feature 17 Wiring a Radio Frequency Module 18 Wiegand Card Reader / Keypad 18 Wiring a Postal Lock Switch 19 Wiring an Internal Camera (CCTV) 19 Power Wiring Power to the Unit 20 Powering up and Checking the LEDs 20-21 Troubleshooting 22 Repair Parts Repair Parts 23-24 “Your” Set-Up “Your” System Diagram and Wiring Configuration 25-26 Accessories 27 FCC and DOC FCC and DOC Requirements 28 Page 2 Dimensions Dimensions Caution! A Static Discharge can Damage Circuit Boards 6 in. 3-15/16 in. 3-1/16 in. 10-1/4 in. 3-1/16 in. 5-1/8 in. Mounting Holes (4) for 5/16 in. 3/4 in. Conduit Hole 3 in. 1-1/4 in. Conduit Hole Knockouts for 5/16 in. Knockouts for 3/8 in. 15 in. AUG 10, 2005 WELCOME 3-1/16 in. 9 in. 1-5/8 in. 2 in. 12 in. 7 in. 9-1/2 in. 6 in. 3-1/16 in. 1-1/2 in. 1/2 in. EL2000 Units EL25 Units Page 3 EL25 Installation EL25 Installation DO NOT overload the removable terminal block connectors. One wire per hole. DO NOT pinch wires when closing and locking the unit. Rotating the Keypad for Vertical Mounting Screw Notch 1 2 3 Bracket Keypad Main Circuit Board Main Circuit Board Connections J200 - Speaker J402 - Light J404 - Call Button Board ONLY Vertical Mounting Position J401 - Keypad J406 - Light J201 - Microphone NOTE: Bracket notch lines up with ribbon cable on keypad. Caution! A Static Discharge can Damage Circuit Boards For EL25 ONLY Caution! A Static Discharge can Damage Circuit Boards 1 Unlock Unit 2 Carefully Lift Cover Up then Slide Out on Hinges 3 Unplug the 2 Main Harnesses 4 Line up Notch with Screw and Push Hinge Out 5 Remove Back Mounting Plate from Cover 1 Disconnect all Plugs from Main Circuit Board and Remove Board. (4 Screws) 2 Remove Bracket. (4 Screws) 3 Rotate Keypad 90 Degrees Clockwise. 4 Reverse the Sequence to Reassemble Unit. NOTE: This unit is for surface mount applications only. Page 4 Unlocking/Locking EL2000 Unlocking EL2000 1. Turn key clockwise 2. Open cover Locking EL2000 1. Turn key counter clockwise to lock position 2. Close cover 3. Apply pressure to left-side until you hear a “click” sound 4. Apply pressure to right-side of unit until you hear a "click" sound 1 2 3 ? 4 5 6 7 8 9 * 0 # # # # 1 2 3 4 5 6 7 8 9 0 * # ? # # # # 1 2 3 ? 4 5 6 7 8 9 * 0 # # 1 2 3 4 5 6 7 8 9 0 * # ? # # # # # 1 2 3 ? 4 5 6 7 8 9 * 0 # 1 2 2 1 3 # 1 2 3 ? 4 5 6 7 8 9 * 0 # # # # # 4 Page 5 1 2 3 ? 4 5 6 7 8 9 * 0 # # # 1 2 3 4 5 6 7 8 9 0 * # ? EL2000 Model Installation EL2000 Installation 1 Unlock Unit 2 Open Cover 3 Unplug the 2 Main Harnesses (Optional) 4 Slide Front Cover Out of Hinges (Optional) 6 Mount Back Housing to Wall or Pedestal 5 Knock-out Desired Mounting Plugs Using Punch NOTE: This unit is for surface and recessed mount ONLY. Page 6 Wire Connections to the Unit Input Board Connections 1. Door 1 Exit Request and Door Status 2. Door 2 Exit Request and Door Status 3. Door 3 Exit Request and Door Status 4. Door 4 Exit Request and Door Status 5. Postal Lock Input 6. AutoCall Input 7. Power 12 VAC Input Output Board Connections 8. Resident Tip/Ring 9. Telco Tip/Ring 10. Relay 4, NO, NC, COM 11. Relay 3, NO, NC, COM 12. Relay 2, NO, NC, COM 13. Relay 1, NO, NC, COM NOTE: All relays are factory set to “Strike” and “10 sec.” DO NOT overload the removable terminal block connectors. One wire per hole. 20-Pin to Main Board 14-Pin to Main Board IO Output Board IO Input Board J2 J3 LED 2 LED 1 RELAY 1 RELAY 2 RELAY 3 RELAY 4 8 9 DOOR STAT 4 EXIT REQ 4 COM 4 3 2 1 5 6 7 10 11 12 13 DOOR STAT 3 EXIT REQ 3 COM DOOR STAT 4 EXIT REQ 2 COM DOOR STAT 1 EXIT REQ 1 COM J5 J7 J6 J4 POSTAL AUTO J1 POWER 12VAC/DC J3 J5 J4 J1 NO NC C NO NC C NO NC C NO NC C LED 4 LED 3 RES TELCO J6 J8 Wire Connections to the Unit Page 7 Wire Specs and Run Distances Wire Specs and Run Distances Use this chart to pull wires in preparation of your installation: Power Wire Specs and Run Distances Description of Wire Run Grounding the Chassis Residence and Telco Phone Lines Door Strike Magnetic Lock Dry Contact Closure (Most Gate Operators) Exit Request (REX) / Auxiliary Open Devices AutoCall Door Status Sensor Barium Ferrite and Wiegand Readers Proximity Readers Radio Frequency Module (RF) Postal Lock CCTV Camera (Optional) Wire Specification 12 AWG Copper 2 Twisted Pairs 18-24 AWG Shielded 2-Conductor 18-22 AWG Shielded 2-Conductor 18-22 AWG Shielded 2-Conductor 18-24 AWG Shielded 2-Conductor 18-24 AWG Shielded 2-Conductor 18-24 AWG Shielded 2-Conductor 18-24 AWG Shielded 5-Conductor 18-24 AWG Shielded 5-Conductor 22 AWG Shielded RG-6 Coaxial 75 ohm 2-Conductor 18-24 AWG Shielded Single Conductor RG-59u Coaxial Maximum Distance 12 feet 5000 feet* 500 feet 500 feet 100 feet 1000 feet (Monitor with a .25 volt p-p composite signal sensitivity) Page 8 9-14 15 15 16 16 17 17 18 18 18 19 19 NOTE: Use metal conduit - run wires in metal conduit instead of PVC pipe. Wires run in PVC conduit may experience interference. Metal conduits also add extra protection against lightning strikes. Never run Telco Wires and High Voltage wires in the same conduit. The high voltage may interfere with the Telco Wires, possibly causing the system to malfunction. * Total distance from Telco to residence regardless of number of units in chain. Distance Under 30 Feet 30 - 75 Feet 75 - 250 Feet 12 VAC Power (Included) 2-Conductor Shielded 14 AWG 14 AWG 14 AWG 12 VDC Power (Not Provided) 2-Conductor Shielded 14 AWG 14 AWG N/A Always provide power from a dedicated source. Plug provided transformer into an outlet wired to its own 10 AMP minimum circuit breaker. This will prevent two problems: • Other equipment cannot introduce spikes, noise, surges or dips into the power circuit that will affect the system. • The system’s operation will not be affected if any other equipment develops a short circuit across the power line. CAUTION: Not responsible for conflicts between the information listed in the above table and the requirements of your local building codes. The information is for suggested use only. Check your local codes before installation. Page 8 Grounding the Units Grounding the Units Ensure that the system is grounded properly. The units contain a number of static sensitive components that can be damaged by static discharge. IMPORTANT: An Earth Ground Rod is Strongly Recommended and should be no further than 12 feet from the unit and use a minimum of 12 gauge wire in most cases. The type and length of earth ground rods vary by region. Contact the building inspector’s office in the municipality where you plan to install the unit for correct grounding materials and installation procedures. Other Ground Sources within 12 ft of Unit Green Ground Wire Earth Ground Rod Ground to Existing Electrical System Electrical Panel Ground to Metallic Cold Water Pipe 12 ft Maximum 12 AGW Minimum 1 2 3 4 5 6 7 8 9 □
   1 2 3 4 10 11 5 6 7 8 9 10 12 11 OR NOTE: Keep ground wire as straight as possible. Before digging, contact your local utility companies, to avoid damaging gas, power, or other underground utility lines. DO NOT ground the units to a pedestal post (gooseneck) if one is used. Page 9 Wiring 1 Unit to Telco Line Wiring 1 Unit to Telco Line The bypass board allows the unit to be disconnected without interrupting normal telephone operation. • When the unit is in use, the bypass switch must be set to the operate position. • When the unit is disconnected, the bypass switch must be set to the bypass position. Tip Ring Tip Ring OPERATE BYPASS Ring HOME Tip Ring TELCO Tip SYSTEM Bypass Board (Mount in the House) (NOT Provided) Ring Tip Ring Tip Home Phone Alarm System Position Use 18-24 AWG 2 twisted pair NOTE: If the unit will be used in conjunction with an alarm system, you MUST connect the telephone line to the alarm system first. If the units are not connected in this order, they will not operate properly. 4 4 3 2 1 3 2 1 Output Board (See page 6) Telco Entrance Box Demarcation Point DO NOT overload the removable terminal block connectors. One wire per hole. IMPORTANT: The Bypass Board (located inside the property) allows access to the phone in case the unit fails. Never run Telco wires and High Voltage wires in the same conduit. The high voltage wires may interfere with the Telco wires, possibly causing the system to malfunction. RES TELCO Page 10 Wiring Multiple Units to Telco Line Wiring Multiple Units to Telco Line Up to 7 units can share the same phone line. The bypass boards allow the units to be disconnected without interrupting normal telephone operation. • When the units are in use, the bypass switches must be set to the operate position. • When the units are disconnected, the bypass switches must be set to the bypass position. Tip Ring Tip Ring RES TELCO Tip Ring Tip Ring RES TELCO OPERATE BYPASS Ring HOME Tip Ring TELCO Tip SYSTEM 4 3 2 1 BYPASS Ring TELCO Tip Bypass Board for Unit 1 Bypass Board for Unit 2 Ring Ring Ring Tip Tip Tip Ring Tip Use 18-24 AWG 2 twisted pair IMPORTANT: You must program the unit ID's for each unit wired in the series. See Keypad Programming Manual. OPERATE BYPASS Ring HOME Tip Ring TELCO Tip SYSTEM 4 3 2 1 Last Bypass Board 4 3 2 1 Home Phone Unit ID 1 Output Board (See page 6) Telco Entrance Box Demarcation Point DO NOT overload the removable terminal block connectors. One wire per hole. IMPORTANT: The Bypass Boards (located inside the property) allow access to the phone in case any of the units fail. Never run Telco wires and High Voltage wires in the same conduit. The high voltage wires may interfere with the Telco wires, possibly causing the system to malfunction. 4 3 2 1 Unit ID 2 Output Board (See page 6) Page 11 Wiring with No Telco Line Wiring with No Telco Line The unit can be a stand alone system that allows communication between the unit and a resident’s phones. Single Unit Tip Ring Tip Ring RES TELCO Use 18-24 AWG 2 twisted pair Output Board (See page 6) NOTE: Ringer Equivalence Number (REN) of “5” maximum. Never run Telco wires and High Voltage wires in the same conduit. The high voltage wires may interfere with the Telco wires, possibly causing the system to malfunction. Multiple Units (Up to 7) Tip Ring Tip Ring RES TELCO Tip Ring Tip Ring RES TELCO To next unit (Unit ID 3 then 4 etc.) Use 18-24 AWG 2 twisted pair IMPORTANT: You must program the unit ID's for each unit wired in the series. See Keypad Programming Manual. IMPORTANT: Only disable the Telco mode of the unit farthest away from the house. See “Disable Telco Mode” in the Keypad Programming Guide. Unit ID 1 Output Board (See page 6) Unit ID 2 Output Board (See page 6) Home Phone NOTE: Ringer Equivalence Number (REN) of “5” maximum. Page 12 Wiring to Dedicated Telco Line Wiring to Dedicated Telco Line IO Output Board LED 2 LED 1 RELAY 1 RELAY 2 RELAY 3 RELAY 4 J3 J5 J4 J1 NO NC C NO NC C NO NC C NO NC C LED 4 LED 3 RES TELCO J6 J8 Tip Ring Tip Ring IO Output Board LED 2 LED 1 RELAY 1 RELAY 2 RELAY 3 RELAY 4 J3 J5 J4 J1 NO NC C NO NC C NO NC C NO NC C LED 4 LED 3 RES TELCO J6 J8 Tip Ring Tip Ring IO Output Board LED 2 LED 1 RELAY 1 RELAY 2 RELAY 3 RELAY 4 J3 J5 J4 J1 NO NC C NO NC C NO NC C NO NC C LED 4 LED 3 RES TELCO J6 J8 Tip Ring Never run Telco wires and High Voltage wires in the same conduit. The high voltage wires may interfere with the Telco wires, possibly causing the system to malfunction. Use 18-24 AWG 2 twisted pair IMPORTANT: You must program the Unit ID's for each unit wired in the series. See Keypad Programming Manual. Unit ID 6 Output Board (See page 6) Unit ID 7 Output Board (See page 6) Use 18-24 AWG 2 twisted pair Telco Entrance Box Demarcation Point Ring Tip Telco Entrance Box Demarcation Point Ring Tip To next unit (Unit ID 5 then 4 etc.) Unit ID 1 is farthest away from Telco Box) Single Unit Multiple Units (Up to 7) Page 13 Wiring to an Internal Phone System Wiring to an Internal Phone System The units can be wired to any Analog Trunk in an internal home phone system. IO Output Board LED 2 LED 1 RELAY 1 RELAY 2 RELAY 3 RELAY 4 J3 J5 J4 J1 NO NC C NO NC C NO NC C NO NC C LED 4 LED 3 RES TELCO J6 J8 Tip Ring Use 18-24 AWG 2 twisted pair Analog Trunk Telco Entrance Box Demarcation Point Internal Phone System Ring Tip EX 1EX 3AnalogEX 4 2 T R Tip Ring Never run Telco wires and High Voltage wires in the same conduit. The high voltage wires may interfere with the Telco wires, possibly causing the system to malfunction. Single Unit Multiple Units (Up to 7) IO Output Board LED 2 LED 1 RELAY 1 RELAY 2 RELAY 3 RELAY 4 J3 J5 J4 J1 NO NC C NO NC C NO NC C NO NC C LED 4 LED 3 RES TELCO J6 J8 Tip Ring Tip Ring IO Output Board LED 2 LED 1 RELAY 1 RELAY 2 RELAY 3 RELAY 4 J3 J5 J4 J1 NO NC C NO NC C NO NC C NO NC C LED 4 LED 3 RES TELCO J6 J8 Tip Ring Tip Ring Use 18-24 AWG 2 twisted pair IMPORTANT: You must program the unit ID's for each unit wired in the series. See Keypad Programming Manual. Unit ID 6 Output Board (See page 6) Unit ID 7 Output Board (See page 6) To next unit (Unit ID 5 then 4 etc.) (Unit ID 1 is farthest away from Telco Box) Analog Trunk Telco Entrance Box Demarcation Point Internal Phone System Ring Tip EX 1EX 3AnalogEX 4 2 T R Tip Ring Page 14 Connection To A NPBI System Connection To An NPBI System IO Output Board LED 2 LED 1 RELAY 1 RELAY 2 RELAY 3 RELAY 4 J3 J5 J4 J1 NO NC C NO NC C NO NC C NO NC C LED 4 LED 3 RES TELCO J6 J8 Tip Ring Tip Ring IO Output Board LED 2 LED 1 RELAY 1 RELAY 2 RELAY 3 RELAY 4 J3 J5 J4 J1 NO NC C NO NC C NO NC C NO NC C LED 4 LED 3 RES TELCO J6 J8 Tip Ring Tip Ring IO Output Board LED 2 LED 1 RELAY 1 RELAY 2 RELAY 3 RELAY 4 J3 J5 J4 J1 NO NC C NO NC C NO NC C NO NC C LED 4 LED 3 RES TELCO J6 J8 Tip Ring Never run Telco wires and High Voltage wires in the same conduit. The high voltage wires may interfere with the Telco wires, possibly causing the system to malfunction. Use 18-24 AWG 2 twisted pair IMPORTANT: You must program the Unit ID's for each unit wired in the series. See Keypad Programming Manual. Unit ID 6 Output Board (See page 6) Unit ID 7 Output Board (See page 6) Use 18-24 AWG 2 twisted pair Sentex Ovation Unit To next unit (Unit ID 5 then 4 etc.) Unit ID 1 is farthest away from Telco Box) Sentex Ovation Unit Single Unit Multiple Units (Up to 7) Page 15 Wiring a Door Strike Lock/Maglock Wiring a Door Strike Lock Wiring a Maglock IO Output Board LED 2 LED 1 RELAY 1 RELAY 2 RELAY 3 RELAY 4 J3 J5 J4 J1 NO NC C NO NC C NO NC C NO NC C LED 4 LED 3 RES TELCO J6 J8 Use 18-22 AWG For DC Power: Install a 1N4005 diode or equivalent. NOTE: The door strike can be connected to any of the 4 relays. Normally Open Common DO NOT use the unit’s power supply for the Door Strike. – + AC or DC Power for Door Strike (Not Provided) DO NOT overload the removable terminal block connectors. One wire per hole. Output Board (See page 6) For AC Power: Install a Siemens S10K30 MOV (Metal Oxide Varistor) or equivalent. IO Output Board LED 2 LED 1 RELAY 1 RELAY 2 RELAY 3 RELAY 4 J3 J5 J4 J1 NO NC C NO NC C NO NC C NO NC C LED 4 LED 3 RES TELCO J6 J8 Output Board (See page 6) Install a 1N4005 diode or equivalent. NOTE: The maglock can be connected to any of the 4 Relays. DO NOT use the unit’s power supply for the Maglock. Use 18-22 AWG – + Normally Closed Common AC or DC Power for Door Strike (Not Provided) For AC Power: Install a Siemens S10K30 MOV (Metal Oxide Varistor) or equivalent. Page 16 Wiring a Gate Operator / Key Switch / PIR / REX Wiring a Gate Operator Wiring a Key Switch/PIR/REX Any auxiliary opening device such as a key switch or PIR (Passive Infrared Device), or an exit request button (REX) that provides normally open contact closure can be hooked up to the Door Input terminals. IO Output Board LED 2 LED 1 RELAY 1 RELAY 2 RELAY 3 RELAY 4 J3 J5 J4 J1 NO NC C NO NC C NO NC C NO NC C LED 4 LED 3 RES TELCO J6 J8 Use 18-24 AWG NOTE: The gate operator can be connected to any of the 4 relays. Normally Open Common DO NOT overload the removable terminal block connectors. One wire per hole. Output Board (See page 6) IO Input Board J2 J3 DOOR STAT 4 EXIT REQ 4 COM DOOR STAT 3 EXIT REQ 3 COM DOOR STAT 4 EXIT REQ 2 COM DOOR STAT 1 EXIT REQ 1 COM J5 J7 J6 J4 POSTAL AUTO J1 POWER 12VAC/DC Use 18-24 AWG NOTE: Additional opening or exit devices can be connected to any of the 4 Exit Request inputs. Exit Request Common Input Board (See page 6) NOTE: Refer to your gate operators owner’s manual for proper relay strike time. Page 17 Wiring a Door Sensing Device / AutoCall Wiring a Door Sensing Device The units can monitor the position of up to four doors/gates and may react to a change in their status with one of the relays (not set as a control relay). For example, if a door is pried open or is held open after its relay deactivates, the unit will record the breach in its transactions and can perform the following actions: • Energize a relay to activate an alarm device such as a siren, light or CCTV camera. • Main use is to terminate strike time early. Wiring the AutoCall Feature Using the AutoCall feature, the unit will automatically call the main residence phone when a driveway sensor is activated (any device that provides a contact closure). For example, when a visitor drives over a loop sensor that is connected to the AutoCall feature, the unit will call the main residence phone automatically so the visitor can speak to the resident without pressing the call button on the unit. IO Input Board J2 J3 DOOR STAT 4 EXIT REQ 4 COM DOOR STAT 3 EXIT REQ 3 COM DOOR STAT 4 EXIT REQ 2 COM DOOR STAT 1 EXIT REQ 1 COM J5 J7 J6 J4 POSTAL AUTO J1 POWER 12VAC/DC Use 18-24 AWG Door Status Common Input Board (See page 6) NOTE: Additional sensing devices can be connected to any of the 4 Door Stat inputs. IO Input Board J2 J3 J5 J6 J4 POSTAL AUTO J1 POWER 12VAC/DC Loop Detector Use 18-24 AWG Common In Loop Sensor Input Board (See page 6) NOTE: Door sensing device should provide contact closure when door is closed. Page 18 Wiring a RF Module / Card Reader / Keypad Wiring a Radio Frequency Module An optional radio frequency module and a remote antenna can be installed if the residents will access a controlled area with a transmitter. Refer to instructions supplied with the optional RF Module for more information. Wiegand Card Reader/Keypad Wiegand card readers and keypads can be connected to either of 2 optional Wiegand modules that can be placed in the unit. Each Wiegand module supports two card readers/keypads. Some Wiegand card reader/keypads have a sixth blue wire. DO NOT connect this blue wire to the unit. Insulate this wire from the unit to prevent a short (Refer to instructions supplied with your Wiegand device for more information). RG-6 Coaxial Connector RG-6 Coaxial Cable 100 Feet Maximum Remote Antenna Avoid any metallic surface around the antenna. RF Module(s) will fit in positions J400 (Device 1) and/or J407 (Device 3) (4 Mounting Screws per Board are Required) 1 RF Module Kit Part # RFMODKT (390 MHz) or Part # RFMODKT3 (315 MHz) J407 Position J400 Position Card Reader is Wired to Device 1 P12V P5V DATA 0 DATA 1 LED COM P12V P5V DATA 0 DATA 1 LED COM J1 J2 J1 J2 Device 1 Device 3 Device 2 Device 4 Red Power Green White Brown Black Shield (Attach to the unit ground only). Blue (Insulate this wire). Use 18-24 AWG 1 Wiegand Module Kit Part # WOMODKT P12V P5V DATA 0 DATA 1 LED COM P12V P5V DATA 0 DATA 1 LED COM Wiegand Modules will fit in J400 as Device 1 (J1) and 2 (J2) and/or J407 as Device 3 (J1) and 4 (J2) (4 Mounting Screws per Board are Required) NOTE: The remote can control 1-4 doors. Page 19 Wiring a Postal Lock Switch / Internal Camera (CCTV) Wiring a Postal Lock Switch - EL25 Models Only The Post Office requires installation of a postal lock if postal carriers do not have access to a controlled area. Contact the local post office and arrange for them to install the postal lock while you are on site. The postal lock requires a switch to activate one of the four relays (Configurable with programming number 69 , in the Keypad Programming Manual). Wiring an Internal Camera [CCTV] An Optional CCTV (Close Circuit Television) camera can be installed inside the unit. Refer to instructions supplied with the camera kit for more information. IO Input Board J2 J3 J5 J7 J6 J4 POSTAL AUTO J1 POWER 12VAC/DC Use 18-24 AWG Common In N.C. Switch Input Board (See page 6) DO NOT overload the removable terminal block connectors. One wire per hole. RG-59u Coaxial Cable 1000 Feet Maximum (Monitor with a .25 volt p-p composite signal sensitivity) A Closed Circuit Monitor Home Entertainment System Contact your dealer/ installer for more information EL2000 EL25 OR NOTE: In the EL2000 models, the postal lock switch is pre-wired. Page 20 Wiring Power to the Unit Wiring Power to the Unit The 110 VAC outlet must be dedicated to the unit ONLY. This outlet should be wired back to its own 10 Amp minimum circuit breaker. This will prevent two problems: • Other equipment cannot introduce spikes, noise, surges or dips into the power circuit. • The system’s operation will not be affected if any other equipment develops a short circuit across the power line. Connect the transformer into a 110 VAC outlet after all connections have been made. Any other type of outlet will cause damage to the system. IO Input Board J2 J3 J5 J7 J6 J4 POSTAL AUTO J1 POWER 12VAC/DC Off Offff OnOn On On OffOff OffOff OnOn OffOff OffOff EL Model Main Room Eug. Rm Oper. Rm Eug. Dept. Manu. 1 Rm Main Dept. Manu. 2 Rm Air (1) Conditioner Air (2) Conditioner Conference Room 1 Conference Rm 2, 3 Refer. Bus 1, 2, 3 Conference Room 2 Comp. Serve 2 Comp. Serve 1 Polarity Does Not Matter (See table on page 7 for AWG) Dedicated 10 Amp Minimum Circuit AC Power 12 VAC or 16 VDC 110 VAC Dedicated Outlet EL Series Unit MUST be Properly Grounded! See Page 8. Input Board (See page 6) Page 21 J500 H2 100A UD H2 100A UD 3D2 100 16B J406 LCD J201 MIC J403 D2 D102 D153 3D2 100 16B 3D2 100 16B 3D2 100 16B H2 100A UD 3D 2 1 0 0 1 6 B J400 + DEVICE 1,2 Description Type Used on Model 1 11 10 9 8 7 6 5 4 3 2 No. Board Label EL25 EL2000 Name LED D300 X X PWR LED Indicates Unit is receiving power Connector J405 X X 20-Pin Connector Connector to IO Input Board. The IO Input Board contains all REX inputs, to IO Input Board DSC inputs and Postal input, Auto Sensor input and Power. Provides power Connector J500 X LCD PWR to LCD Display. Connector J406 X X EL25=LED BOTTOM For the EL25 provides power to bottom lighted LEDs for the main keypad. KEYPAD On the EL2000 this is the top lighted LEDs for main keypad. EL2000=LED keypad Connector J201 X X MIC Microphone connector Connector J403 X X 14-Pin Connector to Connector to the Output Board. The Output Board contains the Resident, Output Board Telco and dry contact Relays. Connector J401 X X KEYPAD Connector for the main keypad LED D2 X X Local Mode Unit supplying Central Office Power to Resident LED D102 X X RES DAA OFF HOOK Resident side of circuit is off hook LED D153 X X TELCO DAA OFF HOOK Telco side of circuit is off hook Connector J301 X X Direct Connect Used for direct connect and handheld programming and Real (Serial Port) Time Monitoring. Connector J404 X X LED Power Supply Connector J407 X X Module Device (3,4) Connect a module (Wiegand or RF) device here. The device address becomes 3 (RF or Wiegand-J1) or 4 (Wiegand-J2) Connector J400 X X Module Device (1,2) Connect a module (Wiegand or RF) device here. The device address becomes 1 (RF or Wiegand-J1) or 2 (Wiegand-J2) Connector J300 X LCD Data Data wires for LCD Display Connector BT300 X X Battery Battery used to back-up the Unit’s real time clock. Switch SW300 X X OV/UV Reset Switch to turn off OV/UV LEDs. This button will turn off the OV/UV LEDs momentarily. If a poor power condition still exists then the OV or UV LEDs may turn on again. LED D513 X X Over-Voltage (OV) Over-Voltage LED. Turns on when the Unit detects an over voltage of 16.5 VAC or 22.3 VDC at power block J1. Measure the voltage at power block J1 to confirm. LED D514 X X Under-Voltage (UV) Under-Voltage LED. Turns on when the Unit detects an under voltage of 9.5 VAC or 10.2 VDC at power block J1. Measure the voltage at power block J1 to confirm. Connector J402 X LED TOP KEYPAD For the EL25, provides power to the top lighted LEDs for main keypad. Connector J200 X X Main Speaker Main Speaker Switch SW500 X X Soft Reboot Reboots firmware without removing power. 13 12 14 17 16 15 18 19 21 20 J407 J401 D300 D513 D514 OV UV J404 J402 LEDJ200 SPKR J300 BT300 DEVICE 3,4 SW300 J405 J301 1 2 3 4 5 6 8 9 10 14 21 20 19 18 17 13 16 15 7 11 12 22 22 Powering Up and Checking the LEDs Wiring Power and Powering Up Unit Page 22 Troubleshooting Troubleshooting Wiring • Check for correct length and AWG of wires. See page 7. • Check that wires are correctly inserted into the terminal blocks (not loose, no two sharing the same position). • Check board markings for correct terminal block placements. • Make sure high voltage and Telco Wires do not share the same conduit. • Use metal conduit, not PVC. No Power To Unit • Check power at source. Power must come from a dedicated 110VAC outlet. • The transformer’s outlet should be wired to its own circuit breaker. • Check “SYS PWR” LED indicators. If “UV” or “OV” are lit, press “PWR MON RST” button. If either of those two LEDs are still lit, check transformer and outlet. Door Strikes/Maglocks/Gate Operator not working • Check power source. Strikes, Maglocks and Gate Operator must be powered independent from unit. • Connect and test different Strike or Maglock. Make sure Strike or Maglock is not defective. • Door Strike: Pin connections “NO” and “COM” at Relay terminal. • Maglock: Pin connections “NC” and “COM” at Relay terminal. • Gate Operator: Pin connections “NO” and “COM” at Relay terminal. Postal Lock or AutoCall device not working • Short “IN” and “COM” pin connections to verify functionality. If wiring is correct and device still does not work, contact technical support. Card Reader not communicating with Unit • Make sure Wiegand is configured to a door (program step 60). • Check Wiegand reader module connections. • Connect and test a functioning reader. Make sure reader is not defective. • Did you add the card(s) to the database while in programming mode? • Check card format compatibility. The unit is only compatible with 26 and 30-Bit. • Review the transactions using Versa XS, if applicable, and check whether card failed. Phone not functioning with the Unit • Did you wire the Bypass Board correctly? See page 10. • Is Bypass Board switch set to “OPERATE”? • Using an alarm system? If so, see page 9. • Using an alarm system on multiple unit configuration? If so, see pages 9 and 10. Aux Open/Exit Request device not working • Did you assign a relay to the REX? See the unit’s programming manual. • Check connections at Door # terminal(s). Wires to “COM” and “EXT REQ #” connection. Transmitter not working • Did you use the correct coaxial cable? See page 7. • Is the remote antenna installed correctly? Is it outside of the unit’s enclosure? • Did you add the transmitter(s) to the database while in programming mode? • Only Passport or Homelink transmitters can be used. Page 23 Repair Parts Repair Parts Installation and Service Information is Available 6 Days a Week Call our Toll Free Number 1-800-528-2806 Monday through Friday 5:00 am to 6:00 pm (Mountain Standard Time) Saturday 7:00 am to 3:30 pm (MST) www.chamberlain.com 17 21 22 18 19 20 16 15 10 13 14 11 11 12 8 9 7 4 5 6 1 2 3 When ordering repair parts, please supply the following information: Description and Model Number Part Description Model Number 19 20 21 22 18 17 16 15 14 Part Description Model Number 1 11 12 13 10 9 8 7 6 5 4 3 2 Silver Cover Nickel Cover Mist Gray Cover Lens Black, Camera Lens Clear, Camera Actuator, Call Button, Silver Actuator, Call Button, Nickel Actuator, Call Button, Mist Gray E-Ring, Call Button Spring, Call Button Gasket, Back Assembly Lock EL25 Focus Key Assembly, Speaker EL25 93D341 93D341-1 93D341-2 108B81 108B81-1 101A159 101A159-1 101A159-2 158A94 177A166 84B81-1 2B809 41B12 2B639 Assembly, LED, Focus Assembly, Mic Cable, EL25 Gasket, Key Pad Assembly Keypad 16 Button Assembly EL25 Main Board Assembly PCB Output Board Focus Assembly PCB Input Board Focus Assembly, Mounting Back, Silver EL25 Assembly, Mounting Back, Nickel EL25 Assembly, Mounting Back, Mist Gray EL25 Assembly, 20-Pin Cable, EL25 Focus Assembly, 14-Pin Cable, EL25 Focus Assembly, Call Button Board Direct Connect Cable 2B721 2B692 84C87 180D236 2B735 2B737 2B736 2C607 2C607-1 2C607-2 2B705 2B704 2B731 2B747 EL25 Parts Page 24 EL2000 Parts Repair Parts Repair Parts Installation and Service Information is Available 6 Days a Week 8 1 2 3 4 6 7 5 16 17 20 9 19 13 12 21 18 22 14 10 15 23 When ordering repair parts, please supply the following information: Description and Model Number Part Description Model Number 19 20 21 22 18 17 16 15 14 Part Description Model Number 1 11 12 13 10 9 8 7 6 5 4 3 2 Assembly Display and Display Board Display Cables Kit Assembly, PCB Output Board Assembly, PCB Input Board Assembly EL Main Board Assembly, 20-Pin Input Board Cable Assembly, 14-Pin Output Board Cable EL2000 Housing Assembly (Black) EL2000 Housing Assembly (Gray) EL2000 Housing Assembly (Nickel) Door Interconnect Cables Kit Assembly, Speaker EL Series Assembly, Call Button Board EL2000 Postal Lock Switch EL2000 41B989 41B990 2B737 2B736 2B735 2B705 2B704 41B991 41B992 41B993 41B994 2B639 41B995 41B996 Interconnect Board Assembly, Lock and Key EL2000 Replacement Key Assembly, Keypad 16 Button Gasket, Keypad Assembly, Mike Cable EL Series Assembly, Entry LED Board Assembly, Keypad Light Board Lens Black, Camera Lens Clear, Camera Gasket and Display Window (Clear) Gasket and Display Window (Black) Faceplate Assembly Black (No Window) Faceplate Assembly Gray (No Window) Faceplate Assembly Nickel (No Window) 41B997 41B999 41B12 180D236 84C87 2B692 41B998 41B773-1 108B881 108B81-1 41B1000 41B1001 41B1002 41B1003 41B1004 23 Page 25 Your System Diagram Your System Diagram Page 26 Your Wiring Configuration Your Wiring Configuration External Access Control Device(s) connected to optional board(s) Device 0 ________________________________________________________________________________ J400 Position on Main Board Device 1 ________________________________________________________________________________ Device 2 ________________________________________________________________________________ J407 Position on Main Board Device 3 ________________________________________________________________________________ Device 4 ________________________________________________________________________________ (Default Internal Keypad) Relay Connections (Output Board) Relay 1 ________________________________________________________________________________ Relay 2 ________________________________________________________________________________ Relay 3 ________________________________________________________________________________ Relay 4 ________________________________________________________________________________ Door Connections (Input Board) Door 1 Connection Door Sensor and/or Exit Device Door 2 Connection Door Sensor and/or Exit Device Door 3 Connection Door Sensor and/or Exit Device Door 4 Connection Door Sensor and/or Exit Device Dealer / Installer Postal Lock Yes No AutoCall Device Yes No CCTV Camera Yes No RF Module Wiegand Wiegand RF Module Wiegand Wiegand Page 27 Accessories Accessories 0 0 4 J 0 0 2 J 204J 604J 102J 7 0 4 J 404J 10 4J 6 0 4 J 0 0 4 J N O C I T I N U W E N e h t k c i l C . 1 t i n U r e t n E d n a e m a N e p y T t i n U 1 , y r t n u o C r e t n E y t i C d n a . v o r P / e t a t S 2 K O k c il C 3 b a T S G N IT T E S L O R T N O C e h t t c e l e S d n a N O C I n o it a r u g if n o C t i n U e h t k c i l C . 2 b a T S R O O D e h t k c i l C . 5 e d i u G t r t S k c i u Q gnisu n o it a l l a t s n I ) s e d o C y r o t F e l g n iS r o F 0 .2 S X a s r e V ” e c i v e D d n a g e i W “ e s o o h C 0 0 4 J r o f 3 o t ” 1 e c i v e D “ e m a n e R ” r e d a e R n a ir t s e d e P “ 5 ” e n o N “ e s o o h C 7 0 4 J r o f 2 K O k c il C 4 ” r o t a r e p O e t a G “ o t ” 1 r o o D “ e m a n e R 1 ” p u o r G e t a G e l c i h e V “ t c e l e S u n e m n w o d - p o r d e h t m o r f 2 d n a ” e t a G n a ir t s e d e P “ o t ” 2 r o o D “ e m a n e R e c iv e D e h t r o f ” r e d a e R n a ir t s e d e P “ t c e l e s 3 ” p u o r G n a ir t s e d e P “ t c e l e S u n e m n w o d - p o r d e h t m o r f 4 E V A S k c il C 5 e h t k c e h c n U ” e c i v r e S e n o h p e le T e s U “ x o b k c e h c 2 e h t n o k c il C n o tt u b ” t i d E “ 1 e t a G n a ir t s e d e P 5 e s e h T . e n il e n o h p e n o h t i w e m o h y li m a f e h t s i t i , e u q i n u s i n o it a c il p p a h l o r t n o c l a t o t e h t t a h t e r u s n e o t r e s u d n e n a ic i n h c e t d e if i l a u q r o / d n a s l a u n a m e h t o ? S E I R E S L E Quick Start Guide Versatile Access Control Programming Software for EL Series Units Versa XS 2.0TM EL25 Camera Kits EL25BWCAMKT (Black & White Camera) EL25DVRCAMKT (Low Lux DVR Color Camera) EL25CAMKT (Color Camera) EL2000 Camera Kits EL2000BWCAMKT (Black & White Camera) EL2000DVRCAMKT (Low Lux DVR Color Camera) EL2000CAMKT (Color Camera) Wiegand Module Kit WOMODKT Wiegand Remote Keypad ESSWOKSG Wiegand Remote Keypad/Prox Combo HIDWOKPRO Versa XS Software VERSWR20 Versa XS RF Module Kit RFMODKT (390 MHz) RFMODKT3 (315 MHz) * # 0 4 5 6 7 8 9 3 2 1 7 8 9 * 0 # 4 5 6 1 2 3 EL2000 EL25 Directory Insert ELDI Heater Kit ELHTRKT EL2000 ONLY Page 28 FCC and DOC Requirements FCC and DOC Requirements FCC Requirements The units comply with Part 68 of the FCC Rules. The label affixed to this equipment contains, among other information, the FCC Registration Number and Ringer Equivalence Number (REN) for this equipment. You must, upon request, provide this information to your telephone company. The REN is useful to determine the quantity of devices you may connect to your telephone line and still have all of those devices ring when your telephone number is called. In most, but not all areas, the sum of the RENs of all devices connected to one line should not exceed five (5.0). To be certain of the number of devices you may connect to your line, as determined by the REN, you should contact your local telephone company. They will tell you what the maximum REN is for your calling area. The following jacks must be ordered from the telephone company in order to interconnect this equipment with the public communication network: None. If your unit causes harm to the telephone network, the Telephone Company may discontinue your service temporarily. If possible, they will notify you in advance. If advance notice is not practical, you will be notified as soon as possible. You will be informed of your right to file a complaint with the FCC. Your Telephone Company may make changes in its facilities, equipment, operations or procedures that could affect the proper functioning of your equipment. If they do you will be notified, in advance, to give you an opportunity to maintain uninterrupted telephone service. Connections to party lines are subject to state tariffs. Contact your local telephone company if you plan to use this equipment on party lines. This equipment cannot be used on public coin service lines provided by the telephone company. DOC Requirements Notice: The Canadian Department of Communications label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational, and safety requirements. The Department does not guarantee the equipment will operate to the user’s satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local Telecommunications Company. The equipment must also be installed using an acceptable method of connection. In some cases, the company’s inside wiring associated with single line individual service may be extended by means of a certified connector assemble (telephone extension cord). The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations. Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment. Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines, and internal metallic water pipe unit, if present, are connected together. This precaution may be particularly important in rural areas. Caution: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate. The Load Number (LN) assigned to each terminal device denotes the percentage of the total load to be connected to a telephone loop, which is used by the device, to prevent overloading. The termination on a loop may consist of any combination of devices subject only to the requirement that the total of the Load Numbers of all the devices does not exceed 100. The Load Number for EL Series Units is 3. 114A2980C ® ™ © 2006 The Chamberlain Group, Inc. All Rights Reserved